User Guide English Manual Version 1.0
10 Tap the chain-link icon to "link" the levels of all connected loudspeakers and subwoofers together. Their faders will "snap" to
11 distorted, (A) reduce the fader's level in the app, (B) reduce the loudspeaker's or subwoofer's volume control setting (on its rear
12 Global Setup Page Tap a Locate button to play a brief tone from that loudspeaker or subwoofer. This is useful if you need to determine which lo
13 Tap and drag the ≡ symbol next to a loudspeaker or subwoofer to reorder it, which affects its placement on the Home Page. Tap the Enable button t
14 DSP Page This page lets you select the DSP setting you want to use on that particular loudspeaker or subwoofer. The available settings diff
15 Tap the button next to your desired setting: Flat (loudspeakers only): There will be no change to the audio. Contour (loudspeakers only): Boosted
16 80 Hz, 100 Hz, 120 Hz, 140 Hz (subwoofers only): Adjusts the low-pass crossover setting. For most applications, we recommend using the 80 Hz or 100
17 Loop Through Crossover Bypass (subwoofers only): Toggles between Standard and Bypass Modes. When the button is off, the subwoofer is in Standard Mo
18 EQ Page This page lets you set your own EQ curve, which will be applied when the loudspeaker's or subwoofer's DSP is set to Cust
19 Tap the EQ Bypass button to allow the signal to ignore the EQ curve. Tap it again to re-enable it. Tap the 80Hz HP button to apply an 80 Hz high-p
2 Table of Contents (Tap a section below to jump to it.) Introduction ... 3 Support ...
20 Advanced Page Tap the Delay Enable button to apply a time delay to the loudspeaker or subwoofer. Tap the ft (feet) or m (meters) field to s
21 speech-only applications, or when used as a delay or fill loudspeaker where the extra bass frequencies are not needed). Tap the Low Pass Filter En
22 Setup Page Tap the white field under the model, serial number, and firmware version to enter a custom name for the loudspeaker or subwoofer. Th
23 Tap the Hardware Password Enable button to set a password to "lock out" other iOS devices from controlling that loudspeaker or subwoofer
24 Tap the Restore button to return all Live Drive app settings to their defaults.
25 Troubleshooting A loudspeaker or subwoofer does not appear in the list of available Bluetooth devices on my iOS device. Make sure the unit is pow
26 On the Home Page, one or more of the loudspeakers or subwoofers is grayed out. Make sure the unit is powered on and within range (100 feet, or 30 m
27 Trademarks and Licenses Alto Professional is a trademark of inMusic Brands, Inc., registered in the U.S. and other countries. App Store, iPad, iP
3 Introduction Support For the latest information about this product (system requirements, compatibility information, etc.) and product registratio
4 Updating the firmware: If there is new firmware available for any connected Black Series loudspeakers or subwoofers, Live Drive will notify you whe
5 Bluetooth Pairing About Range: Black Series loudspeakers and subwoofers use an advanced, extended-range Bluetooth antenna design, allowing for lon
6 3. In your iOS device's list of nearby Bluetooth devices, select one Black Series device to connect to it, and wait until it is fully connec
7 Using Live Drive Getting Started Before using Live Drive, make sure you have done the following: properly set up your Black Series loudspeaker
8 Tap the page name to jump to that section of this user guide. Home Page: This is where you control the volume levels. Tap the icon of a loudspeaker
9 Home Page Tap and drag a fader to adjust its level. You will see the signal output level in the LED meter.
Commentaires sur ces manuels