Alto-professional TMX80DFX Manuel d'utilisateur télécharger pdf (Page 4)

FEATURES

1. MONO INPUTS – Connect a

microphone or line level

instrument to these inputs using

standard XLR or ¼” cable.

2. STEREO INPUTS- Stereo pair

¼” TRS connections. If you

connect only to the left jack, the

input will operate in mono

mode, (the mono signal will

appear on both input channels).

3. LEVEL – Adjusts the channel level (pre-fader and pre-EQ gain).

Adjust this so that the PEAK LED rarely lights up during the

loudest parts of the song.

4. AUX SENDS – The AUX1 (MON) jack can be connected to the

input of an external amplifier or active speaker. For the AUX2

jack, use this to output the AUX2 post fader bus to the inputs of

a stereo multi-effects processor.

5. AUX RETURNS - You can use these stereo 1/4" phone sockets

to return the stereo signal of an effect unit to the Main Mix.

Alternatively you can use them as an extra auxiliary input.

6. HI EQ (TREBLE) – Adjusts the high (treble) frequencies of the

channel.

7. MID EQ – Adjusts the mid-range frequencies of the channel.

8. LOW EQ (BASS) – Adjusts the low (bass) frequencies of the

channel.

9. CTRL ROOM OUTPUT - These 1/4" phone sockets send signal

to a pair of powered monitor speakers or to a PA system.

10. MAIN MIX OUTPUTS - Stereo output controlled by the Main level knob.

11. AUX INPUT - Connect a CD Player, Tape, DAT, iPOD or any other line

level source.

12. AUX OUTPUT - These RCA jacks will route the main mix signal into a

tapedeck or DAT recorder.

13. PHONES - Sends the signal to a pair of headphones.

14. FOOTSWITCH JACK - 1/4'' jack used to connect an external foot switch

to turn on/off the onboard effect module.

15. PEAK LED – When the LED is illuminated, it warns you that you are

reaching signal saturation and possible distortion. Reduce the input level

to avoid distortion.

16. PAN/BAL

- Pan and balance controls to adjust the mono or stereo image

of the signal.

17. GAIN - Adjusts the overall channel volume.

18. AUX - Adjusts the level of the signal sent to AUX buses. AUX1 is

PRE(MON)-FADER, used for monitor applications while AUX2 is

POST(FX)-FADER, used with effect processors.

19. PHONES/CONTROL ROOM LEVEL - Controls the signal sent to the

Control Room and Headphone Output.

20. AUX IN - Controls the signal sent from the AUX IN.

21. OUTPUT LEVEL METERS – Signal level seen as two columns of 8 LEDs.

22. AUX RETURNS - Controls the volume of the processed signal sent to

Main Mix bus.

23. MAIN/AUX – If you push down the AUX TO CONTROL ROOM button, the AUX IN signal will be routed

into the Control Room output and the level will be adjusted by the Control Room knob. If you push down

the AUX TO MAIN MIX button, the AUX IN signal will be routed into the MAIN output and adjusted by the

MAIN MIX LEVEL knob.

24. AUX TO MAIN- Routes the Aux in signal to the MAIN output.

25. PHANTOM PWR Switch - Applies +48 Volt phantom power to the XLR MIC inputs. When condenser

microphones are not used, make sure that the phantom power is disengaged.

26. PHANTOM LED- Indicates when the phantom power is engaged.

27. POWER LED - Indicates when your TMX80DFX powered mixer is switched on.

28. LINE/MUTE SWITCH - When engaged, channels 7/8 output will be muted. By releasing this button, the

LINE IN signal will be sent to the Main Mix.

29. DISPLAY - Displays the selected effect preset.

30. PROGRAM (PUSH) - Adjust this knob to select the effect you wish to use and push this knob to activate

the preset.

31. PEAK LED - LED lights up when the input signal is too strong.

32. FX MUTE Switch

- Activates/deactivates the effects.

1 2 3 4 5 6 7 8 9 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Alto-professional TMX80DFX Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs et amplificateurs Alto-professional TMX80DFX